page . 1 rev.0.1-mar.16.2010 di100s~di1010s ? plastic material used carries underwriters laboratory recognition 94v-o ? low leakage ? surge overload rating-- 30 amperes peak ? ideal for printed circuit board ? exceeds environmental standards of mil-s-19500/228 ? in compliance with eu rohs 2002/95/ec directives mechanical data ? case: reliable low cost construction utilizing molded plastic technique results in inexpensive product ? terminals: lead solderable per mil-std-750, method 2026 ? polarity: polarity symbols molded or marking on body ? mounting position: any ? weight: 0.0105 ounce, 0.3 gram surface mount glass passivated single-phase bridge rectifier maximum ratings and electrical characteristics ratings at 25c ambient temperature unless otherwise specified.single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20% notes: 1. measured at 1.0 mhz and applied reverse voltage of 4.0 volts 2. thermal resistance from junction to ambient and from junction to lead mounted on p.c.b. with 0.5 x 0.5"(13 x 13mm) copper pa ds 406 10.3 0.098(2.5) 0.086(2.2) features recongnized file #e111753 r e t e m a r a pl o b m y s s 0 0 1 i ds 1 0 1 i ds 2 0 1 i ds 4 0 1 i ds 6 0 1 i ds 8 0 1 i ds 0 1 0 1 i d s t i n u e g a t l o v e s r e v e r k a e p t n e r r u c e r m u m i x a mv m r r 0 50 0 10 0 20 0 40 0 60 0 80 0 0 1v e g a t l o v t u p n i e g d i r b s m r m u m i x a mv s m r 5 30 70 4 10 8 20 2 40 6 50 0 7v e g a t l o v g n i k c o l b c d m u m i x a mv c d 0 50 0 10 0 20 0 40 0 60 0 80 0 0 1v t t n e r r u c d r a w r o f e g a r e v a m u m i x a m a 0 4 = o ci ) v a ( f 0 . 1a - e n i s f l a h e l g n i s s m 3 . 8 : t n e r r u c e g r u s d r a w r o f k a e p ) d o h t e m c e d e j ( d a o l d e t a r n o d e s o p m i r e p u s e v a w i m s f 0 3a i 2 ) s m 5 3 . 8 < t ( g n i s u f r o f g n i t a r ti 2 t5 3 7 . 3a 2 s t n e m e l e e g d i r b r e p p o r d e g a t l o v d r a w r o f m u m i x a m a 0 . 1 t a v f 1 . 1v t n e r r u c e s r e v e r c d m u m i x a mt a 5 2 = o c e g a t l o v g n i k c o l b c d d e t a r t at a =1 5 2 o c i r 0 . 5 0 0 5 a ) 1 e t o n ( e c n a t i c a p a c n o i t c n u j l a c i p y tc j 5 2f p ) 2 e t o n ( ( g e l r e p e c n a t s i s e r l a m r e h t l a c i p y tr a j r l j 0 4 5 1 o w / c e g n a r e r u t a r e p m e t e g a r o t s d n a n o i t s n u j g n i t a r e p ot j ,t g t s 0 5 1 + o t 5 5 - o c voltage 50 to 1000 volts 1.0 amperes current
page . 2 rev.0.1-mar.16.2010 di100s~di1010s fig.1 derating curve for output rectified current fig.3 typical reverse characteristics fig.4 max non-repetitive surge current fig.2 typical forward characteristics ambient temperature, c o percent of peak reverse voltage, % no.ofcyclesat60hz instantaneous fwd voltage, volts average forward output current, amperes instantaneous reverse current,ua forward surge current, amperes pk (half sine-wave) instantaneous fwd cuttent, amperes rating and characteristic curves 3.0 2.0 1.0 0 0 50 100 150 1.5 2.5 0.5 t = 100 c a o t=25 c a o 10 1.0 0.1 0.01 0 20 40 60 80 100 120 140 50 40 30 20 10 0 1 2 6 10 20 40 60 100 t=25c pulse width = 200us j o
page . 3 rev.0.1-mar.16.2010 mounting pad layout ? packing information t/r - 1.5k per 13" plastic reel order information legal statement copyright panjit international, inc 2010 the information presented in this document is believed to be accurate and reliable. the specifications and information herein are subject to change without notice. pan jit makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose. pan jit products are not authorized for use in life support devices or systems. pan jit does not convey any license under its patent rights or rights of others. di100s~di1010s
|
